Forum Replies Created

Viewing 15 posts - 1 through 15 (of 25 total)
  • Author
    Posts
  • in reply to: 1927 Flyer #7978
    Springming
    Participant

    I see the “hammer” price was 5300 Pounds

    in reply to: Lydden vintage races Aug 30/31 #7647
    Springming
    Participant

    Wonderful news Roger !!

    Was keeping my fingers and toes crossed for you this time that
    neither yourself or the Scott needed any rebuilding after the event !!

    Regards
    Peter

    in reply to: The "brilliant" – Scott eNewsletter #11 #6515
    Springming
    Participant

    A belated thanks to Steven and Roger for the fine # 11 issue and wishing
    all the best to “Scotters” in particular, and motorcycles enthusiasts in general for 2007 .

    in reply to: Scott on Ebay: – now sold 5.500 GBP #6486
    Springming
    Participant

    Hi Alex, there is also an”oiler assembly” item # 120050793530 (Circa 1929 ??) Maybe wanted by someone in the club ?

    Cheers Peter.

    in reply to: Scott for Sale on Ebay 1935 500 #6476
    Springming
    Participant

    Yes , Apparently it did not reach the reserve on bids but met it during further negotiation, after the auction ended. Cheers Peter.

    in reply to: Scott for Sale on Ebay 1935 500 #6474
    Springming
    Participant

    Seems a good authentic bike….. Went to the US for $11,000 / GBP 5850.

    in reply to: How "economical" is a Scott? #6460
    Springming
    Participant

    I have found with most of my Scotts that the fuel consumption is rather like an aircraft engine and best calculated in time of hours running, rather than MPG.
    Perhaps that is why the “flying flea” Scott aircraft engines were developed !

    Regards to all…Peter.

    in reply to: 10th Scott eNewsletter #6451
    Springming
    Participant

    Upon receipt, as usual, read avidly through without a pause.

    Many thanks to Steven and Roger !!!

    in reply to: part suppliers #6390
    Springming
    Participant

    Jake, here’s another… try https://www.pdrestoration.ca/ . they are in
    Ontario….’phone # is 1-519-652-6200 Cheers Peter.

    PS. If I had your Email would send direct an not bother the Forum…Sorry Folks !!!

    in reply to: part suppliers #6388
    Springming
    Participant

    Hello Jake, you could try “Domiracer” in Cincinatti Ohio USA.

    Email: domiracer@fuse.net. If they can’t help directly they will be able to steer you on !

    Cheers Peter.

    in reply to: Fitting 3 speed kickstart spring #6335
    Springming
    Participant

    Dan,

    Place the spring onto the centrepin and with a pair of pliers (grip firmly) wind the spring up and when wound up set the outer end on the anchor pin .

    Replace the cover an hey presto !

    Cheers Peter.

    in reply to: The cycle of despair continues! #6316
    Springming
    Participant

    Keep at it Dan ! With all your trials and tribulations you will no doubt eventually be amongst the “next generation” Scott guru’s, so stay on the learning curve …it’s all worthwhile. Regards Peter.

    in reply to: www.scotttechnicalities.com.au #6195
    Springming
    Participant

    Excellent Steven…What a good read !!! Regards Peter.

    in reply to: Small end bushes #6073
    Springming
    Participant

    I have used WD 40 in the past, but wether this frowned upon by the
    guru’s I don’t know ..No doubt we shall see… All the best to all the Club members for the festive season. Peter.

    in reply to: Racing results #5972
    Springming
    Participant

    Congratulations to all concerned Roger…What a splendid effort… Paul is certainly the champion. !!!

Viewing 15 posts - 1 through 15 (of 25 total)